English
Español
| Size: | 1/2"-2" |
| Pressure: | 150LB-2500LB |
| Body Material: | WCB, WC6, WC9, CF8, CF8M, CF3, CF3M, CN7M, LC1, LC2, LC3, LCB, LCC, Monel, 20# Alloys, 4A, 5A, C95800, C95500, A105, F304, F304L, F316, F316L, LF1, LF2, LF3, LF9, F51, F53, F11, F22, etc. |
| Seal Material: | PEEK, RPTFE, PTFE, DEVLON, HNBR, NYLON, AFLAS, STELLITE,etc. |
| Connection Type: | Socket Welded, NPT |
| Operation: | Hand lever, gear operated, pneumatic, motorized |
| Face to Face Dimension: | ASME B16.10 |
| Flange End Dimension: | ASME B16.5 |
| Butt Welded Dimension: | ASME B16.25 |
| Design and Manufacture: | API 6D |
| Test Standard: | API 598, API 607, API 6FA, ISO 15848-1-2 |
Screw ends conform to ASME B1.20.1
Available with FNPT and BSP
Available with female thread and male thread
Suitable with forged steel and cast steel material
Seat selection: RPTFE, PEEK, DEVLON and other polymer materials according to different pressure and temperature requirement
Operation device: lever with locking device
Compact structure, small size and light weight
Ball valves can reduce flow, depending on their design and the position of the ball. When the ball is turned perpendicular to the flow, it can create a significant obstruction and reduce the flow rate. However, when the ball is turned parallel to the flow, it allows for a full, unobstructed flow. So, the extent to which a ball valve reduces flow depends on how it is positioned, ball valve manufacture.
Ball valves do not typically reduce water pressure. In fact, they are often used in applications where maintaining high water pressure is important, such as in irrigation systems or industrial processes. However, if a ball valve is not fully open or is partially obstructed, it can cause a reduction in water flow and pressure, gate valve manufacture.
To determine the size of a ball valve, you can check the valve body or the end connections, high temperature gate valves. The size is usually indicated on the valve body or on a tag attached to the valve. If the size is not indicated, you can measure the diameter of the end connections using a caliper or ruler. The most common sizes for ball valves are 1/4 inch, 3/8 inch, 1/2 inch, 3/4 inch, 1 inch, 1 1/4 inch, 1 1/2 inch, 2 inch, 2 1/2 inch, 3 inch, 4 inch, 6 inch, 8 inch, 10 inch, and 12 inch, bronze valve.
To automate a ball valve, you will need to install an actuator onto the valve. The actuator can be electric, pneumatic, or hydraulic, depending on your specific application, carbon steel gate valves. Once the actuator is installed, it can be controlled by a control system, such as a PLC or DCS, to open and close the valve as needed. The control system can be programmed to operate the valve based on various parameters, such as time, pressure, or flow rate. It is important to ensure that the actuator and control system are compatible with the valve and that the installation is done correctly to ensure proper operation, api 6d ball valve.
To disconnect a ball valve, you will need to follow these steps:
1. Turn off the water supply to the valve. 2. Use a wrench to loosen the nuts on both sides of the valve. 3. Once the nuts are loose, use a pair of pliers to hold the valve body in place while you unscrew the nuts completely. 4. Once the nuts are removed, you can pull the valve body away from the pipes.
Note: Be sure to have a bucket or towel handy to catch any water that may leak out when you disconnect the valve, forged ball valve.
Send us a message if you have any questions or request a quote.
A reply from our experts within 24 hours
The latest detailed product catalugue
One-stop service for your project
